3500/05-01-02-00-00-01本特利

产品标题:用于机械状态监控系统 3500/05-01-02-00-00-01本特利Bently监测器仪表

型号： 3500/05-01-02-00-00-01

品牌：本特利

 产品详情资料：

分类： Bently本特利

型号： 3500/05-01-02-00-00-01

产品细节: 3500/05-01-02-00-00-01 3500/05系统机架 绕过所有其他配置的通道

制造商:本特利

产品编号:3500/05-01-02-00-00-01

产品型号:3500/05系统机架

美国制造

机架尺寸:01 = 19英寸机架14个模块插槽)

安装选项:02 =机架安装选项，全尺寸机架(安装到19英寸EIA机架)

代理审批选项:00 =无

保留:00 =无

欧洲合规选项:01 = CE

尺寸(长x亮x高):48.26厘米x 34.92cm厘米x 26.59cm厘米

装运重量:4.5千克

3500/05-01-01-00-00-00测试0K极限的一般方法是输入直流电压并进行调整高于0K上限且低于0K下限，此电压将导致非OK状态，OK继电器改变状态(断电)。鞋面和OK下限显示在测试的Verification (验证) 屏幕中计算机

1.从上的通道端子断开PWR、COM/-和SIG/+现场接线超速检测输入/输出模块。

2.按照第5.1.5.1节(测试设备和软件设置-超速检测系统)。

3.绕过所有其他配置的通道

4.将电源电压调整至-10.00 Vdc.

5,通过短路上的复位触点来复位超速检测模块超速输入/输出模块或启用通道复位软件开关，验证监视器OK指示亮起，并且verification (验证)屏墓的Channel Status (通道状态) 组显示OK (正常) 

6.验证机架接口VO模块上的OK(正常) 继电器是否指示OK(正常(通电) ，参见3500/20机架接口模块操作和维护手册，件号129768-01. 

产品英文详情资料：

Product details: 3500/05-01-02-00-00-01 3500/05 system rack bypasses all other configured channels

Manufacturer: Bentley

Product number: 3500/05-01-02-00-00-01

Product Model: 3500/05 System Rack

Made in the United States

Rack size: 01=19 inch rack with 14 module slots)

Installation option: 02=rack installation option, full size rack (installed into a 19 inch EIA rack)

Proxy approval option: 00=none

Reserved: 00=None

European Compliance Option: 01=CE

Dimensions (length x brightness x height): 48.26 cm x 34.92cm x 26.59cm

Shipping weight: 4.5 kilograms

The general method for testing the 0K limit of 3500/05-01-01-00-00 is to input a DC voltage and adjust it to be higher than the 0K upper limit and lower than the 0K lower limit. This voltage will cause a non OK state and the OK relay to change state (power off). The upper and OK lower limits are displayed on the Verification screen of the test computer

1. Disconnect the PWR, COM/-, and SIG/+field wiring overspeed detection input/output modules from the channel terminals on the.

2. According to section 5.1.5.1 (Test Equipment and Software Settings - Overspeed Detection System).

3. Bypass all other configured channels

4. Adjust the power supply voltage to -10.00 Vdc

5. Reset the overspeed detection module overspeed input/output module or enable the channel reset software switch through the reset contact on the short circuit. Verify that the OK indicator on the monitor lights up and that the Channel Status group on the verification screen displays OK

6. Verify that the OK relay on the rack interface VO module indicates OK (powered on), refer to the 3500/20 Rack Interface Module Operation and Maintenance Manual, part number 129768-01

免责声明：

AMIKON我们销售新产品和停产产品，独立渠道购买此类特色产品。阿米控不是本网站特色产品的授权分销商、经销商或代表。本网站上使用的所有产品名称/产品图片、商标、品牌和徽标均为其各自所有者的财产。带有这些名称,图片、商标、品牌和徽标的产品描述、描写或销售仅用于识别目的，并不表示与任何权利持有人有任何关联或授权。