DS200TCQCG1BJF 溢流板的

产品标题:DS200TCQCG1BJF 溢流板的控制设备

型号： DS200TCQCG1BJF

品牌：GE

                                                                                 产品详情资料：

GE RST 溢出板 DS200TCQCG1BJF 装有 24 个跳线和 3 个 40 针连接器。它还具有 3 个 34 针连接器和 1 个 16 针连接器。分配给 16 针连接器的 ID 是 JC。分配给 40 针连接器的 ID 是 JFF、JE 和 6PL。GE RST 溢出板 DS200TCQCG1BJF 还包含多个继电器，用于打开和关闭板上的电路。继电器无需维护，并通过引线焊接到电路板上。34 针连接器的 ID 为 JFF、1PL 和 JA。40 针连接器和 34 针连接器连接到带状电缆，将 GE RST 溢出板 DS200TCQCG1BJF 连接到驱动器中的其他板和组件。更换电路板时，重要的是要维护电缆驱动器中布置的电缆布线。由于带状电缆传输信号，不正确的布线会引入距离信号电缆太近的电源线的干扰。当信号线和电源线相互平行布线时会发生干扰。好将它们分开。如果它们相互接触，则只能让它们以 90 度角相互交叉。

另一个问题是驱动器依靠自由流动的空气带走组件产生的热量，包括电机。如果带状电缆阻碍驱动器内部关键区域的气流，则它们可能会阻塞气流。这将包括电机周围的空间或空气离开或进入驱动器的通风口附近的空间。

在“联机”选项卡中，单击“一键连接”。在一个步骤中添加连接到服务端口的控制器。编辑程序和配置或以任何其他方式更改控制器上的数据时，您需要“写入”访问权限。写入访问的先决条件只要满足这些先决条件，您就可以对任何控制器进行写入访问。自动写入访问权限不得被任何其他用户占用。手动在FlexPendant上授予远程写入访问权限。出于原因，FlexPendant用户也可以在手动模式下调用此远程写入访问。

                          产品英文详情资料：

The GE RST overflow board DS200TCQCG1BJF is equipped with 24 jumpers and 3 40 pin connectors. It also has three 34 pin connectors and one 16 pin connector. The ID assigned to the 16 pin connector is JC. The IDs assigned to the 40 pin connector are JFF, JE, and 6PL. The GE RST overflow board DS200TCQCG1BJF also includes multiple relays for opening and closing circuits on the board. The relay does not require maintenance and is soldered to the circuit board through leads. The IDs of the 34 pin connector are JFF, 1PL, and JA. Connect the 40 pin connector and 34 pin connector to the ribbon cable, connecting the GE RST overflow board DS200TCQCG1BJF to other boards and components in the drive. When replacing a circuit board, it is important to maintain the cable routing arranged in the cable driver. Due to the transmission of signals through ribbon cables, incorrect wiring can introduce interference from power lines that are too close to the signal cable. Interference occurs when the signal and power lines are routed parallel to each other. It's best to separate them. If they must come into contact with each other, they can only cross each other at a 90 degree angle.

Another problem is that the driver relies on free flowing air to take away the heat generated by components, including the motor. If ribbon cables obstruct airflow in critical areas inside the drive, they may block airflow. This will include the space around the motor or the space near the vents where air leaves or enters the drive.

In the Online tab, click One Click Connect. Adds the controller connected to the service port in a single step.You need Write access for editing programs and configurations or in any other way to change data on the controller.Prerequisites for Write access You can get Write access to any controller as long as the prerequisites are fulfilled.Auto The Write access must not be taken by any other user. Manual The remote Write access must be granted on the FlexPendant. For safety reasons, a FlexPendant user can also recall this remote Write access in manual mode.

免责声明：

AMIKON我们销售新产品和停产产品，独立渠道购买此类特色产品。阿米控不是本网站特色产品的授权分销商、经销商或代表。本网站上使用的所有产品名称/产品图片、商标、品牌和徽标均为其各自所有者的财产。带有这些名称,图片、商标、品牌和徽标的产品描述、描写或销售仅用于识别目的，并不表示与任何权利持有人有任何关联或授权。