FTA端子板51204172-175

厦门阿米控技术有限公司

产品介绍

PlantCruise操作站(HMIWeb)

● 基于霍尼韦尔的HMlWeb技术
● 支持中文界面
● 可视方案图，控制策略设计图的实时监视显示PlantCruise软件
● 监控软件提供高速缓存区的实时动态数据存取、趋势、报警/事件处理、管理、报表报告生成等功能
● 系组态环境PlantCruise组态工作室包括：
◎ 企业模型组态软件Simplified Enterprise ModeIBuilder，对企业中的资产按分级结构直观地描述、显示
◎ 控制策略组态软件ControI BuiIder，为生成控制策略提供全套控制算法库
◎ 系统资源组态软件Quick Builder，用于创建系统硬件
◎ 用户画面组态软件HMIWeb Display BuiIde，用于创建基于HTML格式的操作员图形界面

● 强大的数据交换功能
● 多种其它应用(Uniformance PHD、eServer、EBM等)PlantCruise仿真控制器(SIM)
● 仿真PlantCruise系统
● 基于PC的仿真控制器环境，无须控制器硬件

 FTA端子板51204172-175 MC-TAOY22 MC-PAOY22

产品详情资料

1、 控制室和操作室应具备使用条件：

在安装前，控制室和操作室的土建、安装、电气、装修工程全部完工，室内装饰符合设计要求，空调机启用，并配有吸尘器；

其环境温度、湿度、照明度及空气的净化程度符合DCS系统运行条件才可开箱安装。

2、 对安装人员的要求：

安装人员保持清洁，到控制室或操作室工作换上干净的拖鞋，已防灰尘进入DCS系统装置内；

要尽量避免静电感应对系统元器件的影响，调试时，不穿化纤等容易产生静电的织物。

机、柜、盘运输与安装

机、柜、盘要求整体运输到控制室，安装前拆箱。

DCS系统硬件包装箱在运输、开箱、搬运时小心，防止倾倒和产生强烈振动，以免造成意外损失。

开箱时要有设备供应部门人员和接、保、检部门人员在场共同检查外观质量、设备内部卡件接线的缺陷、系统随机带来的文件、资料等，并做好记录，签字确认。

DCS系统控制室通常有500mm左右的防静电、防潮地板，因此要考虑好底座高度，并保证其稳定性和强度。

接地及接地系统的安装

DCS系统对接地要求较高，一般分为：

本质接地

系统直流工作接地

交流电源的保护接地

保护接地等

各类接地系统、各接地母线之间彼此绝缘。

各接地系统检查无混线后方能与各自母线和接地极相连。

系统直流工作接地要求高，不同家系统要求不同，阻值一般不能超过1Ω，因此打接地极。

其他系统接地要求为接地电阻小于4Ω。

保护接地可以与全厂系统地网相连。

英文产品详细信息

1. The control room and operation room should have the following conditions for use:

Before installation, the civil, installation, electrical, and decoration works of the control room and operation room are all completed, and the indoor decoration meets the design requirements. The air conditioning unit is activated and equipped with a vacuum cleaner;

Only when the ambient temperature, humidity, lighting level, and air purification level meet the operating conditions of the DCS system, can they be unpacked for installation.

2. Requirements for installation personnel:

The installation personnel should maintain cleanliness and wear clean slippers when working in the control room or operation room to prevent dust from entering the DCS system device;

Avoid the impact of electrostatic induction on system components as much as possible. During debugging, do not wear chemical fibers and other fabrics that are prone to static electricity.

Transportation and installation of machines, cabinets, and panels

The machine, cabinet, and panel are required to be transported as a whole to the control room and unpacked before installation.

The DCS system hardware packaging box should be carefully transported, unpacked, and handled to prevent tipping and strong vibration, in order to avoid accidental losses.

When opening the box, personnel from the equipment supply department, as well as personnel from the reception, maintenance, and inspection departments, should be present to jointly inspect the appearance quality, defects in the internal card wiring of the equipment, documents and materials randomly brought by the system, and make records and sign for confirmation.

The DCS system control room usually has an anti-static and moisture-proof floor of about 500mm, so it is necessary to consider the height of the base and ensure its stability and strength.

Grounding and installation of earthing system

The grounding requirements for DCS systems are relatively high, generally divided into:

Intrinsic grounding

System DC working grounding

Protective grounding of AC power supply

Protective grounding, etc

All kinds of earthing system and grounding buses are insulated from each other.

Each earthing system can be connected to its own bus and Earth electrode only after no mixed wires are checked.

The DC working grounding requirements of the system are high. Different systems have different requirements, and the resistance value generally cannot exceed 1 Ω, so the Earth electrode is applied.

The grounding requirement for other systems is that the grounding resistance is less than 4 Ω.

The protective grounding can be connected to the grounding network of the entire plant system.

     FTA端子板51204172-175 MC-TAOY22 MC-PAOY22

3500系列组成部分概述：

3500/70M往复压缩机冲击/速度监测器

3500/72M 活塞杆位置监测器

3500/77M 汽缸压力监测器

3500/63 气体监测器

3500/92 通讯网关

3500/93 LCD 显示装置

3500/94 VGA 显示装置

3500/95 系统综合 PC 显示装置 

3500/40M Proximitor? 监测器模块：通道类型-径向振动、轴向位移、偏心、差胀

3500/42M Proximitor? /位移/速度加速度监测器模块：通道类型-加速度、速度、轴振动

3500/45 位置监测器模块：通道类型-轴向位移、差胀、斜面差胀、壳胀、阀门位置

免责声明：

免责声明： AMIKON我们销售新产品和停产产品，渠道购买此类特色产品。阿米控不是本网站特色产品的授权分销商、经销商或代表。本网站上使用的所有产品名称/产品图片、商标、品牌和徽标均为其各自所有者的财产。带有这些名称,图片、商标、品牌和徽标的产品描述、描写或销售仅用于识别目的，并不表示与任何权利持有人有任何关联或授权。

6AV7881-3AF00-2DN0 6AV7 881-3AF00-2DN0

IPC677C 6AV7894-0BH41-1AE1 6AV7 894-0BH41-1AE1

1FK6063-6AF71-1EH0 1FK6 063-6AF71-1EH0

3TF6844-0C (3TF6844-0CM7 3TF6 844-0CM7)

3TF6844-0CM7 3TF6 844-0CM7

6NG4207-8PS01 6NG4 207-8PS01

6DS1511-8AA 6DS1 511-8AA

S5 6ES5948-3UR22 6ES5 948-3UR22

6SE7015-0EP50-Z 6SE7 015-0EP50-Z

C79458-L2430-A1 C79458L2430A1

CMS71L/BS/TF/AS1H/SB1

3051SFC 3051SFC1CS040N065T32DA1B3G

SRU+60-W-180-3-8-V-DLC

420 6SE6420-2AD31-1CA1 6SE6 420-2AD31-1CA1 B03/1.16

6SE7090-0XX84-0AJ0 + 6SE7090-0XX84-0AF0

MPN 130 MPN130 04510211 KTEN71G2KTSKP

1FK7103-2AF71-1CH1

MP 170 6AV6545-4BC16-0CX0 6AV6 545-4BC16-0CX0

ARI-PREMIO

KPC-ED05 KPC-RECHNER

U 10.380 M 406909

6SE6411-6AD23-0WS8 + 6SE6401-1RB00-0AA0

S7 6ES7614-1AH03-0AB3 6ES7 614-1AH03-0AB3